MENU  •   Set Up  •   Blinking Back the Code  •   Redefining a Key
Punch Through  •   Volume Default  •   Clearing Out
Key Mover  •   Favorite Channel Scan  •   Macro-Sequence

How to Program your One For All® remote

(Model URC-2093)


Set Up

After getting the proper codes from your manual or Customer Service, use the following instructions to enter them into your remote.

  1. Press the device you want to program, then release.
  2. Press and hold the Magic button until the red LED flashes twice, then release.
  3. Enter your 3 digit code.
  4. You should receive 2 quick flashes after entering your code.

menu

Blinking Back the Code:

  1. Tap the device Key - Release
  2. Hold "Magic" until it blinks twice - release.
  3. Press 9 - 9 - 0.
  4. Press 1, Count the number of blinks. (1st digit)
  5. Press 2, Count the number of blinks. (2nd digit)
  6. Press 3, Count the number of blinks. (3rd digit)
If the remote DOES NOT blink it means the number is 0.

menu

Redefining a Key

  1. Hold "Magic" Until it blinks twice.
  2. press 9 - 9 - 2.
  3. press the DEVICE key you want moved
  4. press the DEVICE key you want to replace.
Example: If you want the Aux key to be a TV key:
"MAGIC" (2 blinks) 9 - 9 - 2, TV (you want to move TV)
Then AUX (you want to replace AUX).

menu

Punch Through

This sets Volume to work for one device in all modes.
For example, the TV volume will work in the cable and VCR modes.
  1. Hold "MAGIC" until it blinks twice - release.
  2. Press 9 - 9 - 3.
  3. Press the device key you would like the volume to come from.
You will get two blinks on the remote.
If you want to set the volume for a device to work just one or two other devices- refer to the instructions under "KEYMOVER-From one button to another"

menu

Volume Default

Use this to get Cable or VCR volume to work.
  1. Hold Magic until it blinks twice - release.
  2. Press 9 - 9 - 3
  3. press the VOLUME key, you will get two blinks.
Now The volume is set for all original devices.

menu

Clearing Out

A Device Key - Or Another Button

  1. Tap the device Key - release.
  2. Hold Magic for Two blinks - release.
  3. Press 9 - 9 - 2
  4. Press the button twice. - Two blinks.

All Macro's, and Defaults

  1. Tap the device Key - release
  2. Hold "Magic" for two blinks - release
  3. Press 9 - 8 - 0 -- Two blinks.

menu

Key Mover

From One Button to Another

  1. Hold "Magic" until it blinks twice - release.
  2. Press 9 - 9 - 4.
  3. Tap the DEVICE and the FROM button
  4. Tap the DEVICE and the TO button
  5. Two Blinks
EXAMPLE: To take the volume from a TV and put it in the VCR mode,
it would be: MAGIC - 9 - 9 - 4 -TV - VOL UP - VCR - VOL UP - two blinks.
You would have to do the same process for VOL DN and MUTE.

menu

Favorite Channel Scan

  1. Tap the device key - release
  2. Hold "Magic" until it blinks twice
  3. Press 9 - 9 - 6
  4. Press the channel to be stored, up to 3 digits
  5. Tap the enter button
  6. Repeat steps 4 & 5 up to ten channels
If you do not store ten channels, you have to hold "Magic" for four seconds to close Favorite Cannel programming.
NOTE: To stop scanning, press any other button on the remote control.

menu

Macro-Sequence

This will allow you do do several functions with just the touch of ONE key.
  1. Press the Device key - release
  2. Press "magic" and wait for two blinks - release
  3. Press 9 - 9 - 5
  4. Press the key you want the Macro to be on
  5. Press the sequence of keys you want the remote to do
  6. Press "Magic" and wait for two blinks - release.
      When you hit the key you put the macro on it will automatically start the sequence. IMPORTANT: The Macro key will be the macro in ALL MODES so it is best to pick a key you will not need for anything else in any other mode.

      menu


All Material Copyright ® Universal Electronics Inc.
"One For All" copyright Universal Electronics Inc.
Any questions about the products should be directed to help@ueic.com